Pacifier Clip (Style #1)

 

Who would have thought you could easily customize a functional and stylish soother clip to match any outfit your new baby or child wears?! Our very own, original, incredibly safe, step-by-step tutorial will allow you to do just this… and the possibilities (and outfits) become endless!

Supplies needed:

Step-by-Step Instructions:

*Please note that the recommended length for a pacifier clip in the US is 6-8" for compliance standards. 

1. Loop cord through clip. Leave one side of the cord as a longer piece, and the other end of the cord with about 2.5” of length from the end of the clip.

Pacifier Clip Tutorial - Cara & CoLook the Cord through your Clip - DIY Tutorial - Cara & Co

2. Knot the cord about ½” from the bottom of the clip.

Tie a Knot - Step-by-Step Tutorial - Cara & CoThe Finished Knot - Tutorial - Cara & Co

3. Run your lighter over your knot to fuse the knot.

Fuse Your Knot - Silicone Bead Tutorial - Cara & Co

4. Trim the excess length of the smaller piece of cord at the knot. Carefully melt the tip of the cord and press into the knot until cool and hard.

Snip the Cord - Tutorial - Cara & CoFuse the Knot - DIY Tutorial - Cara & CoReady for Beads - Tutorial - Cara & Co

5. Slightly melt the tip of your length of the cord so that you can begin beading. 

Melt the End of your Cord - Tutorial - Cara & Co

6. Pull the first bead up the cord and over the knot close to the top of the clip.

Thread your first bead - Tutorial - Cara & CoThe bead over the knot - Tutorial - Cara & CoThread the First Bead - Cara & Co

7. Pull the second bead up the cord and over top of the knot near the clip.

Hide the Bead - Pacifier Clip Tutorial - Cara & Co

8. String the rest of the beads onto the cord.

String all the Bead onto the Cord - Tutorial - Cara & CoThe threaded cord - Silicone Bead DIY - Cara & Co

9. Separate the last two beads on your cord from the rest of your beads.

Separate the Last Two Beads - Tutorial - Cara & Co

10. Thread your cord onto your crafting needle and push it back up through the second last bead.

Baby Pacifier Clip DIY Tutorial - Cara & Co

11. Pull the last two beads down until you have about 5 inches of doubled string length between the third last bead and the two end beads.

Dummy Clip Tutorial - Silicone Beads - Cara & Co

12. Tie a knot under the third last bead.

Tie a Knot - Silicone Bead Tutorial - Cara & CoSoother Clip DIY Tutorial - Silicone Beads - Cara & Co

13. Trim the extra length of cord off at the knot so that just the loop is left. Melt the small tip of cord and push it into the knot. Fuse the knot with your lighter.

Trim the Cord - DIY Tutorial - Cara & CoFuse the Knot - Tutorial - Cara & CoNearly Done - Pacifier Clip Tutorial - Cara & Co

14. Pull the second last bead up and over the knot to cover it.

Hide the Knot - Pacifier Clip Tutorial - Cara & CoHidden Knot - Silicone Bead Pacifier Clip Tutorial - Cara & Co

15. Pull the last bead up, and then knot the loop tightly underneath it.

Silicone Pacifier Clip DIY Step-by-Step Tutorial - Cara & CoTie a Knot - Tutorial - Pacifier Clip - Cara & CoFinished Pacifier Clip - Tutorial - Dummy - Soother - Cara & Co

16. It’s done! Safe and easy to use—and best of all, no more lost soothers or teethers! 

Safe Size Measurement for Pacifier Clip - Cara & CoFinished Silicone Bead Pacifier Clip - Cara & Co

We hope you enjoyed this tutorial! Be sure to tag us on instagram using #createdwithcarasuply if you make one yourself, we LOVE seeing your creations!

xo

the girls

 

*At Cara & Co, we take safety seriously. We have had our custom tutorial design above third-party tested by a CPSC accredited testing lab to ensure it meets compliance standards for Canadian (SOR/2011-17) and US (ASTM F963-17) children's pacifier clip requirements. However, this does not remove the responsibility of each customer to ensure that the products they create from this tutorial are tested and meet all relevant compliance standards.

**The products, materials, and supplies sold by Cara & Co. Silicone Craft Supply are intended for use by adults and should never be left unattended with a child.

***Small objects and beads can present choking hazards to young children. Never leave a child unattended with beads or other products. Always dispose of any damaged product. No product is completely indestructible, and fully formed teeth could potentially damage product if chewed aggressively, so responsible attentiveness is needed for any user or purchaser. Customers should always inspect and monitor their products, discontinuing use at the first sight of damage.

****Once our products have been sold and shipped to our customers, Cara & Co Silicone Craft Supply Inc., waives all responsibility and liability from the use of our products. Customers are responsible that their final products made from our supplies meet the appropriate safety requirements for their region. Our buyers understand that by purchasing our products or using suggestions from the above tutorial, the buyer assumes any and all responsibility and liability for the use of the products.

*****Cords, clasps and pacifier clips are not intended to be chewed on and may present choking hazards.


18 comments


  • Cara & Co

    Hi Janelle! We offer our 60" precut lengths of cord that can be found here: https://carasupply.com/collections/cording/products/regular-cord-60
    Hope that helps!
    xo
    Cara


  • Amanda Cavanaugh

    I can’t pull the beads over the knot in the cord… I bought the cord you sell on the website. Maybe it’s too thick?


  • Janelle Schuster

    The instructions on top say to use 60" of string. Is that correct? That would be 5 foot of string. It does not look like you have 5ft. of string. Am I reading that wrong?


Leave a comment

Please note, comments must be approved before they are published