Corded Plant Hanger

Corded Plant Hanger DIY Tutorial


- 50m cord bundle (can be purchased here)

- 15mm accent bead of your choice (can be purchased here). You will need 15 or more beads, depending on how long you make your hanger.

- 60mm beech wood ring (can be purchased here)

- scissors

- large crafting needle (we got ours from a carpet repair needle kit!)



1. Measure out 8 lengths of 10 ft long cord. Cut out 2 additional pieces that are 2 ft in length - these smaller pieces will be used to secure your planter on the top and bottom.

2. Line up your 8 lengths and find the middle point.

3. String your 8 lengths onto the beech ring to the middle point.

4. Line up your cords nicely beside each other so that they lay flat on the beech ring.

5. Take one of your smaller 2 ft lengths. While holding your longer lengths and the wood ring, loop about 3” of the smaller length with a couple inches out at the top.

6. While holding the loop you just created, wrap the longer end of the string around all of the cord pieces. Keep it taught, but not too tight.

7. Keep wrapping the cord around until you’re happy with the length of your wrapped knot. Take the end that you’ve been wrapping around and feed it through the bottom loop you made initially.

8. Reach to the top piece of cord you left out of the knot and gently pull upwards.

9. As you pull upwards, the loop at the bottom will get smaller and close around the bottom piece. Continue to pull until the loop is completely gone and starts to get pulled into the wrapped section of cord.

10. Pull the top cord until you have pulled the loop end to about the middle of the wrapped section. Your wrapped cord should cover the knot being made.

11. When your knot feels secure, trim the smaller pieces left from your 2 ft cord. You should still have 16 pieces of long cord coming out of the knot.

12. Section out 4 pieces of cord that are beside each other.

13. The following knot will be used all through the rest of the tutorial. It is called a square knot. Take the far left string and cross it OVER the middle two cords.

14. Take the far right piece of cord, loop it over and then behind the far left piece you just brought over. Pass it behind the two middle pieces of cord, and forward the loop made between pieces 1 & 2.

15. Pull the knot taught so that the far left and right cord pieces are straight.

16. While keeping the first knot taught, take the far right piece. Cross it OVER the middle two pieces of cord and hold it there.

17. Take the far left piece, loop it over the far right piece you’ve brought over, behind the two middle pieces, and then through the loop between pieces 3 & 4. This is the opposite knot to the first one you just made.

18. Pull the knot tight up against the first one to secure it.

19. You’ve made your first square knot! Yay! Grab another section of four cords beside the first four you were working on and repeat steps 12-18. Do this another 2 times. You should have four knots created, and no extra strings. Be sure to make your knots the same length and placement to keep your hanger balanced.

20. Take one of your four knot groups. Find the two middle cords, and thread your crafting needle on to the end of them. Slide one of your accent beads onto both middle strings.

21. Push the bead all the way up to the first knot you created, without pushing the knot upwards.

22. As you did with the other knots, created a square knot under the accent bead.

23. Continue to thread one bead on the middle two cords of each knot group. You should have four groups with beads, and a square knot under each bead to secure it.

24. Take two side by side knot groups. Take the two far right and two far left cords from each group and pull them together to create a NEW group of four cords. Taking cords from the neighbouring group will start to create the lattice look of the plant hanger.

25. Taking these four new pieces, move down about 4 inches and create a square knot. Once you’ve created your knot, you should have two spare cords hanging down on each side. Take the far right two, and find the next knot group. Take the far left two cords, create a square knot. Go around your cords until all the new knot groups are tied.

26. Repeat threading an accent bead to the two middle cords and securing them with square knots. You should now have two sections of knotted beads on your hanger. Depending on how long you want to make your hanger, keep making knotted bead sections. We made ours 4 sections long.

27. Once you’re happy with the length of your hanger pull all the cords together into one handful.

28. Using the same knot, repeat steps 5-11 to create a wrapped knot. This knot will hold your pot secure, so be sure to make it tight enough to handle a bit of weight.

29. Once your wrapped knot is done, trim the ends to the length that you prefer.

30. Slip your plant pot into the middle of the lattice work of cord. Gently bring it to the bottom knot to sit. We suggest a pot about 4 inches wide.

31. Enjoy your handiwork! If you follow this tutorial, we would LOVE to see what you come up with!

Tag us on Pinterest or Instagram with the hashtag #createdwithcarasupply. And don't forget to water the plants :)!


**The products, materials, and supplies sold by Cara & Co. Silicone Craft Supply are intended for use by adults and should never be left unattended with a child.

***Small objects and beads can present choking hazards to young children. Never leave a child unattended with beads or other products. Always dispose of any damaged product. No product is completely indestructible, and fully formed teeth could potentially damage product if chewed aggressively, so responsible attentiveness is needed for any user or purchaser. Customers should always inspect and monitor their products, discontinuing use at the first sight of damage.

****Once our products have been sold and shipped to our customers, Cara & Co Silicone Craft Supply Inc., waives all responsibility and liability from the use of our products. Customers are responsible that their final products made from our supplies meet the appropriate safety requirements for their region. Our buyers understand that by purchasing our products or using suggestions from the above tutorial, the buyer assumes any and all responsibility and liability for the use of the products.

*****Cords, clasps and pacifier clips are not intended to be chewed on and may present choking hazards.

Leave a comment

Please note, comments must be approved before they are published